145 lines
2.7 KiB
INI
145 lines
2.7 KiB
INI
# This file contains common pin mappings for RAMPS (v1.3 and later)
|
|
# boards. RAMPS boards typically use a firmware compiled for the AVR
|
|
# atmega2560 (though the atmega1280 is also possible).
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
[include mainsail.cfg]
|
|
|
|
[stepper_x]
|
|
step_pin: PF0
|
|
dir_pin: PF1
|
|
enable_pin: !PD7
|
|
microsteps: 16
|
|
rotation_distance: 16
|
|
endstop_pin: ^PE5
|
|
#endstop_pin: ^PE4
|
|
position_min: -39.0
|
|
position_endstop: -39
|
|
position_max: 195
|
|
homing_speed: 50
|
|
|
|
[stepper_y]
|
|
step_pin: PF6
|
|
dir_pin: PF7
|
|
enable_pin: !PF2
|
|
microsteps: 16
|
|
rotation_distance: 16
|
|
endstop_pin: ^PJ1
|
|
#endstop_pin: ^PJ0
|
|
position_min: -13
|
|
position_endstop: -13
|
|
position_max: 195
|
|
homing_speed: 50
|
|
|
|
[stepper_z]
|
|
step_pin: PL3
|
|
dir_pin: PL1
|
|
enable_pin: !PK0
|
|
microsteps: 16
|
|
rotation_distance: 4
|
|
endstop_pin: probe:z_virtual_endstop
|
|
#endstop_pin: ^!PD3
|
|
#endstop_pin: ^PD2
|
|
#position_endstop: 0
|
|
position_max: 200
|
|
|
|
[extruder]
|
|
step_pin: PA4
|
|
dir_pin: PA6
|
|
enable_pin: !PA2
|
|
microsteps: 16
|
|
rotation_distance: 16.842
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: PB4
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PK5
|
|
#control: pid
|
|
#pid_Kp: 22.2
|
|
#pid_Ki: 1.08
|
|
#pid_Kd: 114
|
|
min_temp: 0
|
|
max_temp: 250
|
|
|
|
[probe]
|
|
pin: ^!PD3
|
|
x_offset: -3
|
|
y_offset: -62
|
|
z_offset: 4.1
|
|
samples: 1
|
|
|
|
[safe_z_home]
|
|
home_xy_position: 101, 147
|
|
|
|
[bed_mesh]
|
|
speed: 120
|
|
horizontal_move_z: 25
|
|
mesh_min: 10, 10
|
|
mesh_max: 180, 130
|
|
probe_count: 5, 5
|
|
|
|
[bed_screws]
|
|
screw1: 0, 0
|
|
screw2: 0, 195
|
|
screw3: 195, 0
|
|
screw4: 195, 195
|
|
|
|
#[extruder1]
|
|
#step_pin: PC1
|
|
#dir_pin: PC3
|
|
#enable_pin: !PC7
|
|
#heater_pin: PH6
|
|
#sensor_pin: PK7
|
|
#...
|
|
|
|
[heater_bed]
|
|
heater_pin: PH5
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PK6
|
|
#control: watermark
|
|
min_temp: 0
|
|
max_temp: 130
|
|
|
|
[fan]
|
|
pin: PH6
|
|
|
|
[mcu]
|
|
serial: /dev/ttyACM0
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
max_velocity: 300
|
|
max_accel: 3000
|
|
max_z_velocity: 5
|
|
max_z_accel: 100
|
|
|
|
# Common EXP1 / EXP2 (display) pins
|
|
[board_pins]
|
|
aliases:
|
|
# Common EXP1 header found on many "all-in-one" ramps clones
|
|
EXP1_1=PC0, EXP1_3=PH0, EXP1_5=PA1, EXP1_7=PA5, EXP1_9=<GND>,
|
|
EXP1_2=PC2, EXP1_4=PH1, EXP1_6=PA3, EXP1_8=PA7, EXP1_10=<5V>,
|
|
# EXP2 header
|
|
EXP2_1=PB3, EXP2_3=PC6, EXP2_5=PC4, EXP2_7=PL0, EXP2_9=<GND>,
|
|
EXP2_2=PB1, EXP2_4=PB0, EXP2_6=PB2, EXP2_8=PG0, EXP2_10=<RST>
|
|
# Pins EXP2_1, EXP2_6, EXP2_2 are also MISO, MOSI, SCK of bus "spi"
|
|
# Note, some boards wire: EXP2_8=<RST>, EXP2_10=PG0
|
|
|
|
# See the sample-lcd.cfg file for definitions of common LCD displays.
|
|
|
|
#*# <---------------------- SAVE_CONFIG ---------------------->
|
|
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
|
#*#
|
|
#*# [extruder]
|
|
#*# control = pid
|
|
#*# pid_kp = 23.339
|
|
#*# pid_ki = 0.752
|
|
#*# pid_kd = 181.167
|
|
#*#
|
|
#*# [heater_bed]
|
|
#*# control = pid
|
|
#*# pid_kp = 76.304
|
|
#*# pid_ki = 1.625
|
|
#*# pid_kd = 895.612
|